Datasheet:  Protek-6025C |
 |
| Protek 6025C Analog Oscilloscope 25MHz Description: |
Protek 6025C Analog Oscilloscope 25MHz tests resistors, inductors and capacitors. This analog oscilloscope features an alternate trigger for a stable display of unrelated signals. Free ground shipping within continental USA.
|
| Protek 6025C Analog Oscilloscope 25MHz Characteristics: |
| |
Tests Resistors, Inductors and Capacitors
|
| |
Alternate trigger for a stable display of unrelated signals
|
| |
25MHz Vertical Bandwidth (-3dB)
|
| |
X10 Horizontal Magnification
|
| |
Internal Sync separator circuit for stable triggering of video signals
|
| |
Light weight and low power consumption
|
| |
High brightness CRT with internal graticule
|
| |
X-Y operation
|
| Accessories: |
Operating manual, AC line cord, (2) x1/x10 probes and Test cable
|
| Protek 6025C Analog Oscilloscope 25MHz Specifications: |
| Vertical Amplifer : |
|
| Ch1 and Ch2 |
Sensitivity: 5 mV/Div to 5V/Div in 10 steps (1-2-5 sequence)
Accuracy: ±3%
Bandwidth: (-3dB) DC: 0 to 20MHz AC: 10Hz to 25 MHz
Rise Time: <14.0nS
|
| Input Impedance |
Resistance: 1MΩ +- 5 percent;
Capacitance: 25pF +- 5pF
|
| Input Coupling |
AC, DC GND
|
| Display Modes |
Ch1, Ch2, ALT, Chop, ADD, X-Y
|
| Invert Channel |
Ch2
|
| Maximum Input Volts |
400V DC (DC or AC p-p)
|
| Horizontal Sweep: |
|
| Sweep Times |
200nS/Div to 0.5 Sec/ Div in 20 steps (1-2-5 seq); (x10 Mag: 20nS/Div to 50mS/Div)
|
| Accuracy |
+- 3% (+- 5% X10 MAG)
|
| Sweep Modes |
Normal, X-Y
|
| Triggering: |
|
| Trigger Source |
Ch1, Ch2, ALT, LINE and EXT
|
| Trigger Modes |
Auto, Norm, TV- V, TV-H
|
| Trigger Slope |
Positive or negative adjustable levels
|
| Trigger Coupling |
AC
|
| Trigger Sensitivity |
Int: 20Hz to 2 MHz: 0.5Div 2MHz to 25MHz: 1.5 Div
TV: INt: 1 Div.; EXT: 1V
ALT: 20Hz to 2MHz: 2.0Div 2MHz to 25MHz: 3.0 Div
Ext:20Hz to 2MHz: 200mV 2MHz to 25MHz: 800mV
|
| Ext.Trigger Input: |
|
| Impedance |
1MΩ +- 5% +25pF Capacitance
|
| Max. Input Volts |
400V (DC + AC peak)
|
| X-Y mode: |
|
| Inputs |
X-Axis: Ch1, Y-axis Ch2
|
| Sensitivity |
5 mV/Div to 5V/Div in 10 steps (1-2-5 sequence)
|
| Accuracy |
+- 4 percent
|
| Frequency Response |
(-3dB) DC to = 500KHz
|
| Phase Difference |
< 3 from DC to 50KHz
|
| Component Checker: |
|
| Test Voltage |
Approx. 4.5V RMS open circuit
|
| Test Current |
6.6mA Max short circuit
|
| Test Frequency |
60Hz
|
| Calibrator Signal: |
|
| Waveform |
Square wave
|
| Frequency |
1KHz +- 2%
|
| CRT: |
|
| Size |
8cm x 10cm
|
| Acceleration Volts |
2KV
|
| General Specifications: |
|
| Power Requirements |
AC input Volts: 120V or 220V
|
| Frequency |
50/60Hz
|
| Power Consumption |
35W
|
| Operating Temperature |
0 to 40 C (32 F to 104 F)
|
| Amplitude |
2V +- 2 percent p-p
|
| Dimensions |
12.5"(W) x 5.9"(H) x 18.0"(D)
|
| Weight |
17 lbs
|
Need Technical Advise? Please Call: 602-795-4033
Browse Similar Products |
Testers and Tools 
