Datasheet:  Protek-6030C |
 |
| Protek 6030C 30 MHz Dual Trace Oscilloscope Description: |
Protek 6030C 30 MHz Dual Trace Oscilloscope functions as a digital oscilloscope LCR Component Tester. Free ground shipping within continental USA.
|
| Protek 6030C 30 MHz Dual Trace Oscilloscope Characteristics: |
| |
30 MHz Vertical Bandwidth (-3dB)
|
| |
LCR Component Tester
|
| |
Alternate Trigger for a stable display of unrelated signals
|
| |
X5 Mag for Vertical Input and x10 for Horizontal
|
| |
TV Synch Filter
|
| |
Trigger Signal Output
|
| |
High Brightness CRT with Internal Graticule
|
| Protek 6030C 30 MHz Dual Trace Oscilloscope Specifications: |
| Vertical Amplifier (CH 1 and CH 2) |
Sensitivity 5mV-Div to 20V-Div in 12 steps (1-2-5 seq)
1mV-Div to 4V-Div (X5 Mag)
Mag x5
Accuracy ±3 per cent (5 per cent in X5 Mag)
Bandwidth (-3dB) DC- 0Hz to 30MHz
AC- 10Hz to 30MHz
Rise Time < 18ns (<70ns in X5 Mag)
Input Impedance Res- 1MW ±5 per cent, Cap- 30pF
Input Coupling AC, DC, GND
Invert Channel CH2
CH1/CH2 Trigger Output 100mV-Div into 50W
Display Modes CH1, CH2, ALT, Chop, ADD, X-Y
Maximum Input Voltage 400V (DC or AC peak)
|
| Horizontal Sweep |
Sweep Time 100ns-Div to 0.2s-Div in 20 steps (1-2-5 seq)
10ns-Div to 20ms-Div (X10 Mag)
Mag x10
Accuracy ±3 per cent (8 per cent X10 Mag)
Sweep Modes TV, Normal and Single
|
| Triggering |
Source CH 1, CH 2, ALT, Line and EXT
Slope Positive or Negative adjustable levels
Coupling AC, DC, Normal-TV
Sensitivity (Int) DC to 20MHz 1 Div
Sensitivity (Ext) 0.3V p-p)
Sensitivity (TV Int) 2 Div
Sensitivity (TV Ext) 0.3V p-p
Trigger Lock 50Hz to 10MHz 2 Div
External Trigger Input Impedance- 1MW ±5 per cent
Maximum Input Voltage- 400V (DC or AC p-p)
|
| Z Axis Modulation |
Minimum Input Level TTL
Maximum Input Voltage 50V or AC p-p
Polarity Intensity increases as the voltage decreases
Input Resistance 10KW
Bandwidth (-3dB) DC to 5MHz
|
| X-Y Mode |
Inputs X-Axis (CH1), Y-Axis (CH2)
Sensitivity Same as CH1
Frequency Response (-3dB) DC- 0Hz to 1MHz
AC- 10Hz to 1MHz
Maximum Voltage Same as CH1
X-Y Phase Difference < 3°
|
| Calibrator Signal |
Waveform Square Wave;
Amplitude 0.5V +- 2 percent p-p;
Frequency 1KHz +- 2 per cent
|
| Component Test |
A 60Hz, 9V RMS signal is applied to the CH1 and CH2 input when the AC, DC, GND is in the GND position and the component test button is pushed in.
|
| General Specifications |
CRT 8cm x 10cm (3.15" x 3.94")
Power Requirements AC Input Voltage- 120V or 220V
Frequency 50-60Hz
Power Consumption 35W
Operating Temperature 0 to 40°C (32 to 104°F)
Size 5.1" (H) x 12.2" (W) x 16.45" (D)
Weight 14.3 lbs
|
| Protek 6030C 30 MHz Dual Trace Oscilloscope Accessories Optional: |
| Accessories |
Manual, Line cord, X1X10 Probes (2), Test Leads
|
Need Technical Advise? Please Call: 602-795-4033
Browse Similar Products |
Testers and Tools 
