Datasheet:  Protek-B8400 |
 |
| Protek B8400 4MHz Sweep Function Generator Description: |
Protek B8400 4MHz Sweep Function Generator provides a wide 0.004Hz to 4MHz Frequency range. This sweep function generator features CW/Triggered and Gated modes. Discontinued product - Replaced by Protek B8055.
|
| Protek B8400 4MHz Sweep Function Generator Characteristics: |
| |
Wide 0.004Hz to 4MHz Frequency range
|
| |
CW/Triggered and Gated modes
|
| |
Sweep output and VCG input
|
| |
1000:1 linear sweep and 10,000:1 frequency log sweep widths
|
| |
Settable Sweep Start and Stop Frequencies
|
| |
Low Distortion sinewave
|
| Includes: |
Manual, Line cord, BNC cable
|
| Protek B8400 4MHz Sweep Function Generator Specifications: |
| Frequency Characteristics |
Frequency Range: 0.004Hz to 4MHz in 7 ranges
Ranges: x1, x10x, x100, x1K, x10k, x100k, x1M
Dial Accuracy: 5 percent of full scale
|
| Output Characteristics |
Waveforms: Sine, Square, Triangle, TTL Pulse
High output: Amplitude: 15mV to 10V (into 50W)
DC Offset: 0 to plus/minus 5 into 50W
Impedance: 50ohm
Attenuator: 30dB variable
Low Output: Amplitude:0 to 1V (into 50W)
DC Offset: 0 to plus/minus 0.5 (into 50W)
Impedance: 50ohm
Attenuator: 30dB variable
|
| Sine Wave |
Frequency Range: 0.004Hz to 4MHz
Flatness: plus/minus 2.0 percent (0.004Hz to 400KHz)
plus/minus 10 percent (400KHz to 4MHz)
Harmonic Distortion: < 0.5 percent on the 1K and 10K range
1 percent on the x1, x10, x 100 and x100K ranges
25dBc on the x1M range
|
| Square Wave |
Frequency Range: 0.004Hz to 4MHz
Rise/Fall Time: < 50ns into 50W (High output terminals)
Symmetry: plus/minus 1 percent to 100KHz
plus/minus 5 percent to 4MHz
|
| Triangle |
Linearity: > 99 percent to 200KHz
|
| Opearting Modes |
Modes: Operating modes (CW, Triggered, Gated, Sweep, Manually Triggered)
Trigger/Gate Input Level: TTL
Trigger/Gate Frequency Range: To 4MHz Max.
Trigger/Gate Minimum Pulse Width: < 50ns
|
| Sweep |
Type: Linear and Log
Sweep Time: 30ms to 60 seconds continuously variable
Sweep Width: 1:1,000 linear
1:10,000 log continuously variable
Sweep start and stop frequencies may be set with the Freq dial and the Freq. Stop control
|
| Outputs |
Sync: TTL level
GCV: Output proportional to the selected frequency, 0 to -5V
Sweep: 4V P-P
Impedance: 600Ohm
|
| VCG Input |
Input Voltage: 0 to plus/minus 4V P-P will cause a 1:1,000 frequency change (linear) and 1:10,000 (Log)
Input Impedance: 2KOhm
|
| Operating Temperature |
0 to 50°C (32 to 120°F)
|
| AC Line Voltage |
120/220V, 50/60Hz
|
| Dimensions |
3.5 (H) x 11.4 (W) x 10.6 inches (D)
|
| Weight |
5 lbs
|
Need Technical Advise? Please Call: 602-795-4033
Browse Similar Products |
Testers and Tools 
