Datasheet:  Shimpo-DT-315AEB-230V |
 |
| Shimpo DT-315AEB-230V Stroboscope Description: |
Shimpo DT-315AEB-230V Stroboscope operates independent of line power via an exterior battery pack that can be carried with a convenient shoulder harness or set down to allow the operator full movement for visual inspection.
With this stroboscope, rechargeable batteries power the strobe for approximately four continuous hours, when fully charged. Made in Japan.
|
| Shimpo DT-315AEB-230V Stroboscope Benefits: |
| |
Extraordinary durability yields long service life
|
| |
Lightweight; enables easy portability
|
| |
Eliminates downtime waiting for unit to cool
|
| |
Enables visual analysis of rotating/reciprocating objects through all points of motion/time/angle
|
| |
Fully meets the strictest tolerances
|
| |
Assures stability in changing temperature environments
|
| |
Allows synchronization of the flash rate with the motion of the rotating machinery
|
| |
Allows unit to drive other strobes
|
| |
Prolongs flash tube life
|
| |
Prevents blind viewing areas
|
| |
Permits easy/accurate adjustments to flash rate
|
| |
|
| Shimpo DT-315AEB-230V Stroboscope Characteristics: |
| |
Extruded aluminum construction
|
| |
External battery supply
|
| |
Continuous duty cycle
|
| |
Phase shift (in degrees of delay time)
|
| |
Repeatable accuracy
|
| |
Microprocessor-controlled
|
| |
External trigger
|
| |
Synchronous output
|
| |
Flash timer control
|
| |
Highly polished focused reflector
|
| |
Manual flash controller knob
|
| |
|
| Shimpo DT-315AEB-230V Stroboscope Specifications: |
| INTERNAL MODE |
|
| Flashing Range |
40.0 - 35,000 FPM (flashes per minute)
|
| Accuracy |
+- 0.01 % of reading
|
| Resolution |
0.1 FPM : 40.0 - 5,000 FPM
0.2 FPM : 5,000 - 8,000 FPM
0.5 FPM : 8,000 - 10,000 FPM
1 FPM : 10,000 - 35,000 FPM
|
| Phase Shift |
Use +/- push buttons (360° in 6 seconds)
|
| Display Update Time |
0.2 seconds approx.
|
| Output Signal |
Synchronous, 400 μsec. Pulse output, 0 to +12 VDC amplitude (approx.), 4.7 KΩ impedance
|
| Rate Multiplier/Divider |
Multiply by 2, divide by 2
|
| EXTERNAL MODE |
|
| Flashing Range |
0.0 to 35,000 FPM
|
| Accuracy |
+- 0.01 % +- 1 digit
|
| Phase Shift |
0 to 359 with 1 resolution
|
| Delay Time |
0 to 2,000 μsec from 40 - 10,000 FPM
|
| External Trigger Input Signal |
LO level : 0 -0.8 VDC, HI level : 2.5 - 12 VDC or open collector (NPN), pulse width 50 μsec min.
|
| Input Impedance |
4.7 KΩ to 12 V / 6.8 KΩ to 0 V
|
| GENERAL |
|
| Display |
5 digits, 0.4" (10 mm) high, LED
|
| Flash Tube Power/Life |
Xenon, 10 W max. (100 million flashes)
|
| Flash Duration |
10 - 40 μsec
|
| Sensor Power Supply |
12 VDC (40 mA)
|
| Low Battery Indicator |
Display shows all Ls
|
| Power Requirement |
External battery pack (9.8 - 14.5 VDC, 2.3A)
|
| Operating Temperature Range |
32 - 104 F ( 0 - 40 C )
|
| Weight |
2.5 lb (1.1 kg)
|
| Dimensions |
7.28" L x 4.72" W x 4.72" H (185 mm x 120 mm x 120 mm)
|
| Warranty |
1 year
|
| Standard Accessories |
External battery pack with 220 VAC charger
|
Need Technical Advise? Please Call: 602-795-4033
Browse Similar Products |
Testers and Tools 
